6.1 Status-Line
The first line of a Response message is the Status-Line, consisting
of the protocol version followed by a numeric status code and its
associated textual phrase, with each element separated by SP
characters. No CR or LF is allowed except in the final CRLF
sequence.
Fielding, et. al. Standards Track [Page 38]
RFC 2068 HTTP/1.1 January 1997
Status-Line = HTTP-Version SP Status-Code SP Reason-Phrase CRLF
6.1.1 Status Code and Reason Phrase
The Status-Code element is a 3-digit integer result code of the
attempt to understand and satisfy the request. These codes are fully
defined in section 10. The Reason-Phrase is intended to give a short
textual description of the Status-Code. The Status-Code is intended
for use by automata and the Reason-Phrase is intended for the human
user. The client is not required to examine or display the Reason-
Phrase.
The first digit of the Status-Code defines the class of response. The
last two digits do not have any categorization role. There are 5
values for the first digit:
o 1xx: Informational - Request received, continuing process
o 2xx: Success - The action was successfully received, understood,
and accepted
o 3xx: Redirection - Further action must be taken in order to
complete the request
o 4xx: Client Error - The request contains bad syntax or cannot be
fulfilled
o 5xx: Server Error - The server failed to fulfill an apparently
valid request
The individual values of the numeric status codes defined for
HTTP/1.1, and an example set of corresponding Reason-Phrase's, are
presented below. The reason phrases listed here are only recommended
-- they may be replaced by local equivalents without affecting the
protocol.
Status-Code = "100" ; Continue
| "101" ; Switching Protocols
| "200" ; OK
| "201" ; Created
| "202" ; Accepted
| "203" ; Non-Authoritative Information
| "204" ; No Content
| "205" ; Reset Content
| "206" ; Partial Content
| "300" ; Multiple Choices
| "301" ; Moved Permanently
| "302" ; Moved Temporarily
Fielding, et. al. Standards Track [Page 39]
RFC 2068 HTTP/1.1 January 1997
| "303" ; See Other
| "304" ; Not Modified
| "305" ; Use Proxy
| "400" ; Bad Request
| "401" ; Unauthorized
| "402" ; Payment Required
| "403" ; Forbidden
| "404" ; Not Found
| "405" ; Method Not Allowed
| "406" ; Not Acceptable
| "407" ; Proxy Authentication Required
| "408" ; Request Time-out
| "409" ; Conflict
| "410" ; Gone
| "411" ; Length Required
| "412" ; Precondition Failed
| "413" ; Request Entity Too Large
| "414" ; Request-URI Too Large
| "415" ; Unsupported Media Type
| "500" ; Internal Server Error
| "501" ; Not Implemented
| "502" ; Bad Gateway
| "503" ; Service Unavailable
| "504" ; Gateway Time-out
| "505" ; HTTP Version not supported
| extension-code
extension-code = 3DIGIT
Reason-Phrase = *
HTTP status codes are extensible. HTTP applications are not required
to understand the meaning of all registered status codes, though such
understanding is obviously desirable. However, applications MUST
understand the class of any status code, as indicated by the first
digit, and treat any unrecognized response as being equivalent to the
x00 status code of that class, with the exception that an
unrecognized response MUST NOT be cached. For example, if an
unrecognized status code of 431 is received by the client, it can
safely assume that there was something wrong with its request and
treat the response as if it had received a 400 status code. In such
cases, user agents SHOULD present to the user the entity returned
with the response, since that entity is likely to include human-
readable information which will explain the unusual status.
Fielding, et. al. Standards Track [Page 40]